Ask filmmakers what gives away a low-budget film, and many will say the sound before the picture. Viewers forgive a soft or grainy image far more readily than dialogue they can’t understand. The good news: clean dialogue depends more on technique than on expensive gear. This guide covers the microphones, where to put them, how to set your levels, and the habits that save hours in the edit.

Record sound separately from the camera

Most cameras, and especially phones and DSLRs, have weak built-in microphones and noisy preamps, and they sit in the wrong place: on the camera, far from the actor’s mouth. The usual approach on indie sets is dual-system sound: a microphone feeds a dedicated audio recorder, while the camera records its own “scratch” audio. In editing, you line the two up.

  • Sync with a slate or a clap. At the start of each take, clap a slate (or your hands) in view of the camera. The sharp spike in both recordings is your sync point. Most editing programs can also sync automatically by matching the scratch audio.
  • Or use timecode. Recorders and cameras that share timecode line up automatically; it saves time on bigger shoots.

Shotgun vs. lavalier: which microphone, when

Shotgun or boom micLavalier (lav) mic
Pickup patternDirectional (supercardioid or hypercardioid): hears what it points atUsually omnidirectional: hears all around, but it’s inches from the mouth
Where it goesOn a boom pole, above the actor, just out of frameClipped or taped to the actor, often hidden in clothing
SoundNatural, with some of the room’s characterClose and consistent, sometimes a bit boxy; can pick up clothing rustle
Best forMost dialogue scenes, when someone can operate the boomWide shots, walk-and-talks, noisy places, interviews, solo shoots
Watch out forEchoey rooms, a boom dipping into frame, boom shadowsFabric rub, sweat, wireless dropouts, mics showing on camera

Professional sets often use both: a boom on every take and lavs on the actors, recorded to separate tracks, so the editor can choose the better one line by line.

Indoors, especially in small rooms with hard walls, a long shotgun can pick up the room’s reflections and sound hollow. Many sound mixers prefer a shorter shotgun or a hypercardioid “pencil” mic indoors, and save long shotguns for exteriors.

Boom technique

  1. Get as close as the frame allows. Distance is the biggest factor in clean sound. Ask the camera operator where the top of the frame is, then bring the mic just above it.
  2. Point at the mouth. From above, angle the mic down toward the actor’s mouth. Off-axis, a directional mic sounds thinner and duller.
  3. Follow the dialogue. In a conversation, swing the mic from speaker to speaker. Learn the lines so you’re on the next actor before they start.
  4. Mind the light. A boom can cast a shadow on actors or walls. Work with the gaffer to find an angle the lights don’t catch.
  5. Hold it steady. Grip the pole lightly, keep the cable wrapped so it doesn’t tap the pole, and use a shock mount. Handling noise travels straight up the pole.
  6. Always wear closed-back headphones. If you can’t hear a problem on set, you’ll hear it in the edit.

Hiding a lav

  • Placement: the center of the chest, roughly a hand’s width below the chin, so the sound stays consistent when the actor turns their head.
  • Stop the rustle: tape the mic so clothing can’t rub against its head. Sound crews use soft tapes, fabric patches, and purpose-made lav mounts; a small loop of cable taped near the mic stops pulls on the cable from reaching it.
  • Watch the fabrics: stiff synthetics and layered jackets are the noisiest. Cotton is kinder.
  • Wireless: transmitters can drop out. Many current wireless kits can also record internally in each transmitter as a backup; switch it on.

Recorder settings and levels

  • Sample rate and bit depth: 48 kHz is the standard for film and video. Record at 24-bit or, if your recorder offers it, 32-bit float.
  • Levels: with 24-bit recording, set the gain so normal dialogue sits well below the top of the meter, with loud moments peaking around −12 to −6 dBFS. Digital audio that hits 0 dBFS clips, and clipped sound can’t be fixed.
  • 32-bit float: recorders with 32-bit float capture an enormous range, so a sudden shout won’t clip in the file, and you can adjust the level later. It’s a real safety net, but it doesn’t help with a mic that is too far away, pointed the wrong way, or overloaded by a very loud sound right at it.
  • Phantom power: most shotgun mics need 48 V phantom power from the recorder, sent down a balanced XLR cable. Check the mic’s requirements.
  • Low-cut filter: a gentle cut around 80 Hz removes rumble from traffic and handling. Use it with care; you can’t add back what you cut.

Control the location

The quietest microphone can’t fix a noisy room. Before you roll:

  • Turn off what hums: refrigerators, air conditioning and heating, fans, fluorescent lights, and phones. A common trick is to leave your car keys in the fridge you switched off, so you can’t leave without turning it back on.
  • Tame echo: rugs, curtains, sofas, and moving blankets hung off-camera all soak up reflections. An empty room with bare walls is the hardest place to record.
  • Outside: use a foam windscreen indoors and a furry windshield (a “dead cat”) or a full blimp outdoors. Wind noise ruins more exterior dialogue than anything else.
  • Plan around noise: scout at the same time of day you’ll shoot. Listen for planes, schools letting out, traffic, and construction.

Room tone and wild lines

Room tone is 30 to 60 seconds of the location’s silence, recorded with everyone still and the mic in its usual position. Every room has its own faint hiss and hum, and editors use room tone to fill gaps between lines so the background doesn’t drop out at every cut. Record it at every location, every time.

Wild lines are lines recorded without the camera, right after a take, when a plane ruined the dialogue or an actor turned away from the mic. Recording them on set, in the same space, matches far better than re-recording weeks later in a studio.

Common mistakes

  • Relying on the camera’s built-in microphone.
  • Recording with no headphones, so nobody hears the fridge, the wind, or the clipping.
  • Setting the gain too low “to be safe,” then boosting it in editing, which raises the noise along with the voice.
  • Skipping room tone.
  • Booming from below in a wide shot, which picks up footsteps and points the mic at the ceiling’s reflections.

Try it: record the same line four ways: with the camera’s built-in mic from six feet away, a shotgun at three feet, a shotgun at one foot just out of frame, and a lav on the chest. Listen on headphones without looking at which is which. The difference between three feet and one foot usually surprises people more than the difference between microphones.

Listen for it on IFN

Dialogue-driven shorts are a good ear-training exercise: listen to how close the voices feel and how the background holds steady across cuts. Try these, then browse the library:

For specific microphones, recorders, and starter kits by budget, see our guide to camera and sound gear for indie filmmakers. And when your film is done, submit it to IFN, free.

Sources: Ric Viers, The Location Sound Bible (Michael Wiese Productions), on boom and lav technique, room tone, and wild lines; manufacturers’ documentation for 32-bit float recorders and wireless lavalier systems, on internal recording and headroom. Level ranges are common practice for 24-bit dialogue recording; follow your recorder’s manual.